There is no single "gutter price" — and any contractor who quotes one over the phone without seeing your roof is guessing. A realistic 2026 number for a typical single-family home is $1,050 to $5,200 for 150 to 200 linear feet of aluminum gutters, which works out to roughly $6 to $40 per linear foot installed across common materials. The spread is wide because a few real drivers swing the total hard. Here is what they are, and where your home likely lands.
The national range, and why it is a range
Most homes need 100 to 200 linear feet of gutter, and the all-in installed cost for common materials runs $6 to $40 per foot — climbing to $40 to $100-plus for copper and ornamental work. Translated to a whole house:
- Low end — $1,050 to $1,800. A small home under 1,500 sq ft, one story, in vinyl or basic sectional aluminum, with a simple gable roofline, in a competitive labor market.
- High end — $4,000 to $5,200-plus. A 2,000 to 3,000 sq ft home, two or more stories, in seamless aluminum or steel, with a complex roofline, in a Northeast or West Coast labor market, with gutter guards included.
- Premium — $8,000 to $15,000. Copper on a large home, where the material alone carries most of the cost.
If a quote you receive sits far outside these bands in either direction, that is your cue to ask why — not to assume it is wrong, but to understand which driver is pushing it.
Cost by material — the biggest lever you control
Material is the single largest cost lever on the entire job. The gutter you choose moves the price more than anything else, so it is the first decision to get right. Installed per-linear-foot in 2026:
- Vinyl — $3 to $9/LF. Cheapest and DIY-friendly, but it gets brittle in cold and sags over long runs. Best for mild climates and tight budgets.
- Aluminum, sectional — $6 to $12/LF. The workhorse: rust-proof, light, widely available. More seams than seamless, which means more potential leak points.
- Aluminum, seamless — $8 to $15/LF. Roll-formed on site to the exact length of each run. Costs 15 to 30 percent more than sectional but eliminates most joints.
- Galvanized steel — $9 to $20/LF. Stronger than aluminum and the common pick in freeze-thaw climates where buyers want a heavier gauge.
- Copper — $15 to $40/LF mid-market, $100-plus/LF ornamental. Beautiful, decades-long lifespan, and priced accordingly. A large copper job can reach $8,000 to $15,000.
Seamless vs. sectional
Seamless gutters require on-site roll-forming equipment and specialized labor, so expect a 15 to 30 percent premium over sectional. The trade-off is fewer leak points — seams are where sectional gutters fail first. For most homeowners staying put long-term, seamless aluminum is the better value despite the higher up-front cost.
Standard 5-inch vs. 6-inch
Standard 5-inch K-style is the baseline. Upgrading to 6-inch — common for high-rainfall regions or large roofs that shed a lot of water fast — adds $2 to $4/LF to the base material cost. It is often worth it where downspouts would otherwise overflow in a hard storm.
What moves your quote
Two identical-looking homes can get very different quotes. These are the honest drivers, roughly in order of impact:
- Material grade. The biggest lever, as above. Vinyl to copper is a 5x-plus swing per foot.
- Linear footage and home size. Cost scales roughly linearly with footage. Small homes (1,000–1,500 sq ft) average 100–140 LF; medium (1,500–2,500 sq ft) average 140–200 LF; large (2,500–4,000 sq ft) average 200–300 LF.
- Story count and height. Two-story homes cost 15 to 25 percent more than single-story because of scaffolding, safety gear, and a slower work pace. Three-plus stories add 20 to 40 percent above baseline.
- Roof complexity. Hip roofs with multiple planes add 10 to 20 percent over a simple gable. Multiple dormers add 15 to 30 percent. Steep pitch over 6:12 increases labor 10 to 20 percent.
- Seamless vs. sectional. The 15 to 30 percent seamless premium, as covered above.
- Regional labor market. Northeast and West Coast labor runs 25 to 40 percent above the national median; the South runs 10 to 20 percent below. More on this below.
- Season and urgency. Fall (Sept–Nov) and spring (March–May) are peak — expect a 10 to 20 percent premium and 2 to 4 week waits. Summer is slowest, and a 10 to 15 percent discount is common. Rush or emergency installs add 20 to 30 percent.
- Fascia condition. Rotted or damaged fascia must be replaced before gutters can hang — that adds $6 to $12/LF for fascia alone, or $9 to $34/LF if soffit replacement is also needed.
- Permits. Most areas do not require one for replacement, but where they do, fees run $50 to $200. Verify locally.
The line-item breakdown
A complete gutter quote is more than the gutter itself. Here is what shows up on a thorough estimate in 2026:
- Gutter material only (aluminum sectional): $1 to $3/LF.
- Labor: $4 to $10/LF, national median around $5 to $7/LF — 30 to 50 percent of the total installed cost, at roughly $65 to $75/hr.
- Downspouts: $5 to $12/LF installed for vinyl/aluminum, $9 to $12/LF for steel, $17 to $20/LF for copper. A typical home needs 3 to 6.
- Downspout extensions: $10 to $50 per unit in materials, $30 to $100 per unit installed.
- Old gutter removal and disposal: $0.65 to $2/LF in removal labor, plus $100 to $350 for hauling. Flat-rate removal is often quoted at $100 to $500 total.
- Fascia board replacement: $6 to $12/LF (fascia only), $9 to $34/LF (fascia plus soffit). A minor section repair runs $100 to $400.
- Gutter guards / leaf protection: $3 to $25/LF installed — screen/mesh $3 to $8/LF, micro-mesh (LeafFilter-type) $10 to $25/LF. Whole-home average: $500 to $2,500.
- End caps, miters, hangers: end caps $2 to $10 each, elbows $4 to $8 each, hangers $2 to $17 each — usually folded into the per-foot labor quote. Complex custom miters can add $10 to $25 per corner.
- Splash blocks: $6 to $66 each, depending on concrete vs. decorative.
- Heat tape / de-icing cable (cold climates): $1 to $6/LF — a full 150 LF install runs $150 to $900.
- Gutter flashing: around $20/LF where required at roof-wall intersections.
Gutter cost by region
Where you live moves the per-foot price as much as the material does. Installed aluminum, by region in 2026:
- Northeast (NY, NJ, CT, MA, PA): $10 to $20/LF, averaging $12 to $16. High union labor rates, dense metros, ice-dam risk that often calls for larger 6-inch gutters, and heavy fall-foliage demand.
- South (TX, FL, GA, NC, SC): $7 to $14/LF, averaging $9 to $12. A competitive contractor market and lower wages. Heavy Southeast rainfall (40–55 in/yr) often needs more downspouts, adding 10 to 15 percent to scope.
- Midwest (IL, OH, MI, MN, WI): $8 to $15/LF. Good contractor availability keeps pricing competitive, but freeze-thaw cycles push buyers toward heavier-gauge steel, raising material cost.
- West Coast (CA, WA, OR): $10 to $18/LF. High metro labor costs (Seattle, Portland, Bay Area, LA). Dry summers enable off-season discounts, and wildfire-prone areas require non-combustible metal, ruling out vinyl.
- Mountain West / Rockies (CO, UT, NV): 15 to 30 percent above the national average, driven by a limited contractor pool and access difficulty.
- Southwest (AZ, NM): $7 to $13/LF. Low rainfall reduces complexity, though monsoon regions need careful downspout routing.
When it costs more, when it costs less
To set expectations honestly:
- You will pay more if: you choose seamless aluminum, steel, or copper; your home is two or three stories; your roofline has hips, valleys, and multiple dormers; you add gutter guards; you book in peak fall or spring; your fascia is rotted; or you live in the Northeast, West Coast, or Mountain West.
- You will pay less if: you choose vinyl or sectional aluminum; your home is one story with a simple gable roof; your existing fascia is sound; you book in the summer slow season; and you are in the South or Southwest.
The most reliable way to get a real number is an on-site measure of your actual linear footage, roofline, and fascia condition. Use the bands here to sanity-check the quotes you receive — if one is far above or below, ask which driver explains the gap.
How shops quote and collect a gutter job
Pricing the job is only the first step — you still have to measure the home, present the material options, win the approval, and collect before you pull off the ladder. That is where the right tool earns its keep. Claver for gutters lets you build a per-foot pricebook once, send a clear quote with material options from the driveway, take a deposit to lock the install date, and invoice with card, ACH, or consumer financing when the work is done — so the price you measured is the price you actually collect. See how it fits on the gutters page or browse the full guides hub.